DriveAxis Industrial Automation Blog

Blog

“If I size by motor nameplate, I’ll be fine” — why that breaks for two real cases, and which VFD survives

Posted on Wednesday 17th of June 2026 by Jane Smith

ABB vs Delta VFD — Question: You pick a drive by the motor’s full-load amp (FLA) rating. That’s the standard thumb-rule. [...]

Continue Reading →

Posted in Blog

Blog

“But the motor nameplate says 30 A …” — Why Real Watts Trump FLA When Sizing an ABB vs Danfoss VFD

Posted on Wednesday 17th of June 2026 by Jane Smith

ABB vs Danfoss VFD — One question, three cases. You have a 7.5 kW fan motor that draws 28 A full load at 400 V — 19.4 kVA on paper. The VFD catalogue says “7.5 kW / 30 A.” Should you buy the next size up? [...]

Continue Reading →

Posted in Blog

Blog

ABB vs Delta VFD: The 120 % Overload Myth That Cost a Plant $4 000 / yr

Posted on Wednesday 17th of June 2026 by Jane Smith

ABB vs Delta VFD — Opening statement (myth bust): “A 150 % overload rating beats 110 % — so the smaller VFD saves panel space, right?” That sounds like common sense until you realise the one-minute duty cycle of that 150 %… [...]

Continue Reading →

Posted in Blog

Blog

3 Reasons a “Maintenance-Light” Panel Will Fail—and Which VFD Breaks First

Posted on Wednesday 17th of June 2026 by Jane Smith

ABB vs Danfoss VFD — The myth: “A maintenance-light panel means you can ignore the VFD until the motor burns up.” In reality, a “light” panel usually means no spare parts on the shelf, no scheduled PM, and a single point of… [...]

Continue Reading →

Posted in Blog

Blog

ABB ACS880 vs Delta MS300 VFD: what the datasheet hides

Posted on Wednesday 17th of June 2026 by Jane Smith

ABB vs Delta VFD — You are standing in front of a 150 kW fan with a 30-second ramp requirement. The purchasing agent hands you two datasheets: an ABB ACS880 and a Delta MS300. [...]

Continue Reading →

Posted in Blog

Blog

ABB vs Danfoss VFD: What the Datasheet Hides

Posted on Wednesday 17th of June 2026 by Jane Smith

ABB vs Danfoss VFD — You just bought a 7.5 kW motor for a positive-displacement pump. The datasheet says both drives can run it. But after six months, one will trip on overcurrent while the other keeps the process running. [...]

Continue Reading →

Posted in Blog

Blog

ABB vs Delta VFD: Runtime Under Real Load — What the 150% Overload Rating Really Means

Posted on Wednesday 17th of June 2026 by Jane Smith

ABB vs Delta VFD — Popular claim: “A Delta MS300 rated for 150 % overload for 60 seconds is tougher than an ABB with only 110 % for 1 minute — so it can run harder, longer.” Sounds decisive on paper, but that number alone tells… [...]

Continue Reading →

Posted in Blog

Blog

ABB vs Danfoss VFD: runtime under real load – the efficiency curve myth

Posted on Wednesday 17th of June 2026 by Jane Smith

ABB vs Danfoss VFD — The popular claim: “A Danfoss VLT drive delivers longer runtime under real load because its application-optimized HVAC/AQUA variants squeeze more efficiency at partial load than a general-purpose ABB drive.”… [...]

Continue Reading →

Posted in Blog

Blog

“How much of that efficiency curve are you actually going to get?” — ABB ACS580 vs Delta MS300

Posted on Wednesday 17th of June 2026 by Jane Smith

ABB vs Delta VFD — You’ve got a load that needs a VFD. You see two numbers: ABB ACS580 at up to 98% efficiency, Delta MS300 at up to 97%. The gap is one point — you could almost ignore it. [...]

Continue Reading →

Posted in Blog

Blog

<span class="quote">“The data sheet says 97 %, but after three months it was closer to 93.”</span> — ABB vs Danfoss VFD: Efficiency You Can Actually Keep

Posted on Wednesday 17th of June 2026 by Jane Smith

ABB vs Danfoss VFD — I’ve had this conversation more times than I can count: an engineer buys a drive that claims 97 % efficiency at full load, installs it in a cooling-tower application with 40 °C ambient and a lot of part-load… [...]

Continue Reading →

Posted in Blog